DC Power Onboard with Newmar’s DC Power Conditioners. Newmar’s power array of dc conditioners provide stabilizing voltage during engine crank, voltage stabilizers with Isolated DC-DC converters, electronic noise filters and automatic power selectors. Whether there is a need for seamless redundant power system tie-in for critical electronic loads, the need for VHF and GPS fish finders to stay on during engine crank, or battery back-up for sensitive electronic devices.

Download PDF Data Sheet

StartGuard™
Provides Voltage Protection
During Engine Start

The abrupt DC system voltage drop that accompanies engine starting can cause microprocessor-based voice and data transmitters to “dump” programmed memory.

StartGuard solves this problem by providing supplemental voltage to sensitive electronics while the engine is cranked. It contains a sealed rechargeable battery which is switched on-line to electronics when the starter switch or solenoid is engaged. When the engine is running StartGuard automatically goes off-line and the internal battery is recharged by the alternator.

Specifications
Input Voltage: 13.8 - 14.8 VDC nominal, 15.5 VDC max.
Relay Activation Input Voltage: 7-15 VDC
Output: 20 amps max.
Battery: 12 VDC , sealed rechargeable, 5 - 7 year life (typical) 4 amp-hour capacity
Certified by DOT and IATA for shipment by air Replacement battery P/N: 591-0412-0
Back-up Capacity (Fully Charged): (See matrix below)

Model

Input

Back-Up Capacity

Dimensions

Weight

1 Minute

2 Minutes

Inches

Centimeters

Lbs

Kg.

NS-12-20

13.8-14.8 VDC Nominal
15.5 VDC Max

20 amps

18 amps

5.5

2.5

8.25

4.9

3.5

20.1

12.5

8.9

NAV-PAC®
Mobile communication electronics such as programmable two-way radio and data transceivers, vehicle location systems and other microprocessor-controlled devices require clean and steady DC input power. Their sensitive circuitry is highly vulnerable to voltage drop from engine start, noise and line spikes from alternators and motors, and conducted noise from various other electronic devices. NAV-PAC prevents all of these problems.

• Prevents voltage ”drop-out” to
electronics during engine start
• Absorbs line "spikes"
• Filters out electrical interference
• Provides supplemental voltage/battery
back-up for up to 15 min.
• Remote monitor panel included.

NAV-PAC has been successfully employed for years by thousands of Fire Trucks and other Emergency Service vehicles nationwide

U.S. PATENT #: 5172292

Model: NP-12, NP-24
Output: 20 amps Max. @ 12 Volt; 15 amps Max. @ 24 Volt
Back-Up Power:
8 Amps for fifteen (15) minutes
12 Amps for eight (8) minutes
18 Amps for two (2) minutes
Battery: Sealed Rechargeable 4.0 Amp-Hour, 5-7 years typical life, can be replaced. Low-voltage disconnect circuit
protects battery from total discharge. Certified by DOT and IATA for shipment by air.
Noise Filtering: Audio through 200 MHZ
Voltage Spike Protection: Transient energy capability; 100 Joules, 4,000 amps Max (8 x 20 micro seconds)

Model	Input	Back-Up Capacity		Dimensions						Weight
		1 Minute	2 Minutes	Inches			Centimeters			Lbs	Kg.
NP-12	13.8-14.8 VDC Nominal, 15.5 VDC Max.	20 amps	15 amps	H	W	D	H	W	D	5.9	2.7
				5.25	6.2	7.2	13.3	15.7	18.8
NP-24	27.6-29.6 VDC Nominal, 31.0 VDC Max	20 amps	15 amps	6	7.75	7.5	15.24	17.14	19	8	3.6

Panel Dimensions: 3.5” W x 2” H (8.9 x 5.1 cm)

12 & 24 Volt Stabilizing Converters

Feed sensitive electronics with proper voltage regardless of battery condition. These stabilizing converters provide continuous, precisely regulated output over the entire range of a battery's usable voltage. This prevents subjecting loads to fluctuating input voltage which can cause shutdown, diminish performance and possibly damage sensitive circuitry.

These converters provide total input/output isolation, virtually eliminating conducted line noise and permitting connection of negative ground loads to positive or floating ground systems, or vice versa. They can also be modified for use as battery chargers, allowing maintenance of a battery at a great distance from the charging source, providing reserve power if the main source fails. The rugged anodized aluminum case is ideal for mobile applications

Application Benefits Include:
• Operate electronics at optimal input voltage, even from nearly drained batteries
• Boost voltage to compensate for voltage drops in long wire runs from batteries
• Eliminate voltage drops during momentary high current drain from batteries, as during engine start
• Eliminate voltage fluctuation from charge sources
• Eliminate voltage overshoot due to sudden removal of high current load

Specifications

Model	Input	Output	Output Amps
Model	Range	Voltage	Int.	Cont.
12-12-12I	10-16 VDC	13.6 VDC	12	8
12-12-35I	10-16 VDC	13.6 VDC	35	20
48-24-3I	20-56 VDC	24.5 VDC	3	3
48-24-6I	20-56 VDC	24.5 VDC	6	4
48-24-9I	20-56 VDC	24.5 VDC	9	5
48-24-18I	20-56 VDC	24.5 VDC	18	10

Options/Factory Modifications
• Operation as a battery charger (contact factory)
• Parallel/redundant operation (contact factory)
• High vibration mounting kit (see bottom of page)
• Non-standard output voltage (contact factory)

Mobile DC UPS
Mobile Data Power System

The Mobile Data Power, model MDP-25, is a DC UPS that solves the common problem of lengthy reboot sequences, system crash, data and hard drive corruption in mobile computer work stations due to a low voltage and loss of power as a result of intermittent or poor vehicle battery condition. In addition, the MDP provides a low voltage output warning signal to terminals (such as Motorola® MW 800 series work stations) allowing orderly automatic shutdown of the powered device, protecting data and preventing hard drive corruption.

Utilizing a high speed sensor circuit, when primary vehicle voltage drops below a critical point, the internal 9AH battery is switched on-line in milli-seconds, assuring no interruption to the powered device(s). The MDP-25 has an internal 3 step, temperature compensated charger that maintains its reserve battery at full charge, ready to go on-line when a fault or degradation of primary vehicle battery occurs. This functionality assures continued operation of mobile computers under a variety of adverse vehicle battery conditions.

Housed in a rugged aluminum case and heavy duty mounting plate, the unit is designed for installation in emergency vehicles, service and other utility vehicles that require a steady source of voltage for mobile computers, work stations, and electronics. LEARN MORE

Noise Filters
The interference or electronic “noise” generated by alternators, ignition systems, motors, etc., can render an emergency vehicle’s radio, data transceivers or other electronic equipment virtually useless. This interference takes the form of popping or static on radios or audio gear and garbled images or “hash” on video displays.

These specialized filters can be used singly or in combination to attenuate conducted line noise, either at the affected equipment or at the noise source.

Models:
150A - Alternator filter, 150 amps
PC-10 - Affected equipment filter, 10 amps,
PC-25 - Affected equipment filter, 25 amps,

Filter Features:
• Heavy duty aluminum construction
• Operate on 6-48 VDC systems
• Integral mounting flanges for secure installation
• Nickel-plated brass stud connectors on alternator filters accommodate high current cables and terminals
• Color coded wire leads on all other models make in-line installation easy

Automatic Power Selector
The Automatic Power Selector (APS) is a solid state device which enables installation of a seamless, redundant power system for critical electronic loads. It selects the higher voltage of two isolated DC power sources and routes power to the load. Should one source falter or fail, the other will automatically supply the load with no transfer delay, operation continues uninterrupted.

Easy installation, two independent power sources are wired to the APS and routed in a single output to the vital load. Rugged, rust-proof anodized aluminum case.

Model APS-70:
Voltage Rating: 6-50 VDC, neg. ground
Peak Load Current: 70 amps
Size: 3.25" x 4.5" x 3.1"
Weight: 2 lbs.


Extreme vibration mounting kit The Extreme Vibration Mounting Kit is available to protect NEWMAR power converters from the extreme stresses of shock and vibration when mounted on high–vibration vehicles. The kit (pictured here) replaces the standard vibration kit provided with the unit and fits into the unit's mounting flange to act as a "super shock absorber" for electronics in high-vibe applications. It is available to fit all NEWMAR units from 2 to 70 lbs. Specify KIT–L for units which weigh 2–15 lbs. and Kit–H for units which weigh 16-70 lbs.